Security Link SL150 Anleitung zur Fehlerbehebung Seite 30
- Seite / 144
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
SL150 Installation and Setup Guide
4–8
Typical summary display
Zn ZT RC In RT
07 77 3C HW: 1
A summary display will appear, showing the data for
zone 07 that was just programmed. If it is programmed
satisfactorily, press [
✱
] to continue.
Program Alpha?
0 = No 1 = Yes 0
The next request is to enter an Alpha descriptor for zone
7. Since this is a keyswitch zone, no descriptor is
required. Enter “0”.
Enter Zn Num.
(00 = Quit) 08
Since “0” (no) was entered above, the system will
display a prompt for entry of the number for the next
zone.
Press [0] [0] plus [
✱
] to exit
✱
56
mode.
Exit the programming mode by keying
✱
99
.
Keyswitch Operation
To arm AWAY, turn key and release within a 1/2 second. To arm STAY, turn and hold key
for longer than 2 seconds. To disarm, turn key and immediately release.
LED Indications
Green Red Meaning
OFF OFF Disarmed & Not Ready
ON OFF System Ready
OFF On Steady Armed Away
OFF Slow Flash Armed Stay
OFF Rapid Flash Alarm Memory
Programming Basic Hardwired Zones
Each zone must be programmed into the system using the
✱
56 Zone Programming mode,
which assigns characteristics that define the way the system responds to faults on that zone.
Refer to Section 14: Zone Response Type Definitions and Section 16: Zone
Programming for specific instructions on programming hardwired zones.
Checkout Procedure for Hardwired Zones
After installation and programming of all hardwired devices is completed, the security
system should be checked, as follows.
1.
Make certain that all devices and sensors connected to the hardwired zones are not in a
faulted state. Doors and windows with contacts should be closed, PIRs should be covered
(use a cloth to mask them temporarily, if necessary).
2.
Plug in the AC transformer if you have not already done so.
With all hardwired zones intact, the Alpha keypad connected to the system should display:
✱ ✱
SYSTEM READY
✱ ✱
If the following is displayed,
NOT READY Press
✱
to show faults
press
✱
to display the faulted zone(s). Restore any faulted zone(s) as necessary (also make
sure that you have connected a 2000 ohm
EOL resistor
across the terminals of unused zones).
When the
SYSTEM READY
message is displayed, you can proceed to the next step.
- 6HF XULW\6\VWHP 1
- Table of Contents 4
- List of Figures 7
- Introduction 9
- FINAL POWER 12
- Installing the Control 13
- RCVR BRD 15
- TERMINALS 16
- ON CONTROL 16
- Wiring the AC Transformer 17
- Installing the Backup Battery 18
- Earth Ground Connections 18
- Installing Remote Keypads 19
- Mounting the Keypads 20
- AUX. DATA 21
- Basic Hardwired Zones 1–8 23
- Remote Keyswitch (Zone 7) 27
- Wired Zone Expansion 33
- Wireless Expansion 37
- 1 2 3 4 5 38
- Installing the 5800TM Module 39
- Jam Detection and Reporting 39
- Appendix A 42
- Powerline Carrier Devices 47
- Programming Relay Outputs 48
- 4285 & 4286 VIP Module 49
- Section 11: 50
- Audio Alarm 50
- Verification (AAV) Unit 50
- 4285/4286 51
- VIP MODULE 51
- External Sounders 53
- Sounder Connections and Power 54
- Sounder Supervision 54
- Testing the Sounder 54
- Long Range Radio 55
- Dynamic Signaling Feature 56
- 4285 or 4286 58
- Final Power-Up 59
- Battery Tests 60
- Mechanics of Programming 61
- Loading Factory Defaults 63
- Exiting the Programming Mode 63
- Data Field Descriptions 69
- OUTPUT TO LONG RANGE RADIO 74
- Allows 81
- Zone Programming 83
- 86
- To Remove a Zone 88
- Section 16 -Zone Programming 91
- Output Device Programming 93
- Zone Lists 99
- Alpha Descriptor Programming 101
- Adding Custom Words 103
- ALPHA VOCABULARY LIST 105
- CHARACTER (ASCII) CHART 105
- Macros (SpeedKey) 107
- Remote Programming and 109
- Control (Downloading) 109
- Remote Programming Commands 110
- Initial Download 110
- System Communication 111
- System Operation 115
- Keypad Functions 116
- Testing the System 121
- Troubleshooting Guide 123
- POSSIBLE CAUSE REMEDY 124
- SYMPTOM POSSIBLE 124
- CAUSE REMEDY 124
- CONTACTING TECHNICAL SUPPORT 125
- In This Section 127
- APPENDIX A 131
- Regulatory Agency Statements 133
- Warnings and Limitations 135
- DOC LOAD NO.: 3 143
- ¬19'l 144
- Two Mid America Plaza 144
- Suite 200 144
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Security Link SL150
(29 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern